{"id":6652,"date":"2026-07-31T10:30:32","date_gmt":"2026-07-31T02:30:32","guid":{"rendered":"https:\/\/belirollforming.com\/?p=6652"},"modified":"2026-08-04T12:04:27","modified_gmt":"2026-08-04T04:04:27","slug":"roll-forming-for-warehouse-racking","status":"publish","type":"post","link":"https:\/\/belirollforming.com\/fr\/roll-forming-for-warehouse-racking\/","title":{"rendered":"Roll Forming for Warehouse Racking EN 15512: 6 Vital Compliance Points"},"content":{"rendered":"
\n\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Introduction<\/h2>

Selling warehouse racking profiles to European buyers means passing EN 15512.<\/p>

This standard defines structural design rules for adjustable pallet racking systems. If your roll forming for warehouse racking does not meet its requirements, your profiles fail certification. That means rejected shipments and lost contracts.<\/p>

EN 15512 sets rules for steel grades, load combinations, connection strength, and dimensional tolerances. Every one of these rules flows back to your roll forming process. Hole pitch in upright posts. Yield strength of cold-formed sections. Beam connector fit after coating.<\/p>

This guide covers six EN 15512 compliance points for roll forming for warehouse racking. Each point explains what the standard requires and what you must verify on your warehouse racking roll forming machine.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t\t\t\t\t\t

What Is EN 15512?<\/h2>

EN 15512:2020+A1:2022 is the European standard for steel static storage systems. It covers adjustable beam pallet rack systems. Both braced and unbraced frames fall under its scope.<\/p>

The standard was updated in 2020 with a key change. The material reduction factor (gamma M) moved from 1.0 to 1.1. This made designs 10 percent more conservative. It also aligned EN 15512 more closely with\u00a0Eurocode 3<\/a>. The standard is maintained by\u00a0CEN\/TC 344<\/a>, the European technical committee for steel static storage systems.<\/p>

EN 15512 works with three companion standards. EN 15620 covers tolerances and deflections. EN 15629 handles equipment specification.\u00a0EN 15635<\/a>\u00a0covers use and maintenance. For seismic zones, designers add EN 16681.<\/p>

A\u00a0machine de profilage \u00e0 cadre vertical soud\u00e9<\/a>\u00a0for European warehouses must produce profiles that pass all four standards. The roll forming for warehouse racking process must align with each one.<\/p>

The EN 15512 Standards Ecosystem<\/h2>
Standard<\/th>Port\u00e9e<\/th>Impact on Roll Forming for Warehouse Racking<\/th><\/tr><\/thead>
EN 15512<\/td>Structural design principles<\/td>Load cases, material factors, connection strength, testing<\/td><\/tr>
EN 15620<\/td>Tolerances, deflections, clearances<\/td>Upright verticality limits, beam deflection L\/200, hole pitch tolerances<\/td><\/tr>
EN 15635<\/td>Use and maintenance<\/td>Load signage per bay, periodic inspection schedules<\/td><\/tr>
EN 16681<\/td>Seismic design<\/td>Extra bracing and connection rules for earthquake zones<\/td><\/tr><\/tbody><\/table>

Each standard feeds requirements back to the warehouse racking roll forming machine. If your\u00a0profileuse verticale \u00e0 grande vitesse<\/a>\u00a0produces uprights with hole pitch deviation above EN 15620 limits, the racking system fails installation checks.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t\t\t\t\t\t

6 EN 15512 Compliance Points for Roll Forming<\/h2>

1. Material Selection and Steel Grade Requirements<\/h3>

EN 15512 Clause 7 sets steel material rules. Cold-formed sections need steel with guaranteed mechanical properties. Minimum yield strength for cold-formed steel is 140 N\/mm squared. For hot-rolled sections it is 200 N\/mm squared.<\/p>

European racking manufacturers use S235 to S355 grades. S355 is common for heavy-duty uprights and pallet racking roll forming applications. Higher yield strength lets designers use thinner gauge. That directly affects your roll forming for warehouse racking. Thinner gauge at higher strength needs tighter roller gap control. Tooling wear runs faster on harder material.<\/p>

The standard also covers fracture toughness. Cold-formed sections below 5 mm used above minus 30 degrees Celsius need no special check. But profiles for cold storage at minus 28 degrees Celsius need documented toughness from the steel mill.<\/p>

A\u00a0machine de profilage \u00e0 rouleaux \u00e0 poutre \u00e9tag\u00e9e<\/a>\u00a0running S235 versus S355 needs different roller pressure. Operators must adjust per grade to avoid over-rolling.<\/p>

Key compliance steps for warehouse racking roll forming machine operators:<\/strong><\/p>